Fiberlock IAQ 6100 Mould-Resist Coating

$679.00 Inc. GST

SKU: 106019

A Clear 100% acrylic water-based coating with anti-fungal agents clear mould resistant used by professionals to prevent mould from growing on the dry coating surfaces.

In Stock


Have a question or need a quote? Ask Our Experts

Live Chat | 1300 121 586 | Email

Category: SKU: 106019

Description

FiberLock IAQ 6100 features a 100% acrylic water-based coating and anti-fungal agents which prevents mould from growing on dry surfaces. This product is used by professional for dry coating on surfaces such as wood, plaster, wallboard, sheetrock, concrete, masonry block, primed metal, and galvanized metal.

 

FEATURES

  • Tested by independent laboratories for mould resistance: ASTMG-21 and ASTM D-3273
  • Mould resistant*
  • 100% acrylic

*Resistant to mould growth on the dry coating surface only

 

How to Use

SURFACE PREPARATION

Surfaces to be coated must be free of dust, mildew, mould, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap and other surface contamination. Clean mould stained surfaces with Advanced Peroxide Cleaner, or use an EPA registered antimicrobial disinfectant cleaner such as IAQ 2000, IAQ 2500, ShockWave or ShockWave RTU. Patch irregularities with vinyl patching paste or an appropriate patching compound. IAQ 6100 is self-priming over bare sheetrock, composition board, ceiling tile and concrete.

WALLBOARD, SHEETROCK, GYPSUM BOARD

Joint cement should be sanded smooth, but avoid abrading the paper.

APPLICATION TOOLS

Apply IAQ 6100 with brush, roller or airless spray equipment.

PRODUCT APPLICATION

IAQ 6100 is supplied ready to use, but can be thinned sparingly with water (up to 200mL per 4L) for proper application consistency if necessary. Apply IAQ 6100 generously and uniformly by brush, roller, or airless spray. Apply one coat of IAQ 6100 and ensure that the finished surface is properly sealed. To ensure that the finished surface is properly sealed, two-coats may be required on some porous surfaces.

COVERAGE

  • Smooth Surfaces- 32-55m². 4 liters
  • Porous Surfaces- 23-27m². 4 liters

DRYING TIME

  • @ 22°C 50% R.H
  • To Touch – 1 Hour
  • Recoat – 4-8 Hours

CLEANUP

Clean tools and drippings with warm soapy water before Fiberlock IAQ 6100 dries. Dispose of all waste according to all existing local, state and federal regulations.

PRECAUTIONS

Store in a dry place at temperatures between 4.5°C and 32°C. Stir thoroughly. Do not mix with any other coatings, solvents or colors in oil. The IAQ 6100 coating is resistant to mould only on the surface of the coating. No mould resistance claim is made other than to the coating itself. The use of this product does not protect users or others against food-borne or disease-causing bacteria, viruses, germs or other disease-causing organisms. Do not apply when air or surface temperature is below 10°C, or when drying conditions are poor or when surfaces are above a 15% moisture level content. Use adequate ventilation during application. When applying with a sprayer, wear a NIOSH approved respirator with any R, P, N or HE filter. For interior use only.

Additional information

Weight 19 kg
Dimensions 30 × 30 × 38 cm
Size

Weight Per Gallon ± .5 lbs: 8.7 lbs/gal

Packaging Type

5 Gallons

Solids by Weight ± 2%

28.4%

Solids by Volume ± 2%

25.3%

Viscosity at 70°F

87-93 Kreb Units

Specular Gloss

20º ± 3 @ 60º

Flash Point

Non-combustible

Shelf Life

36 Months Min. (Original Sealed Container)

Coverage Smooth Surfaces

350-600 ft2/gal

Coverage Porous Surfaces

250-300 ft2/gal

Drying Times

@ 70 – 77°F , 50% R.H.

Drying Times: to touch

1 hour

Drying Times: to recoat

4-8 hours

Drying Times: Minimum Application Temp

50º (10ºC)

Reviews

There are no reviews yet.

Be the first to review “Fiberlock IAQ 6100 Mould-Resist Coating”

Fiberlock IAQ 6100 SDS